XenonzcarImporter: Fix: convert markdown link syntax to wiki syntax; remove broken self-anchor links

2026-05-16T23:33:19Z

Fix: convert markdown link syntax to wiki syntax; remove broken self-anchor links

← Older revision		Revision as of 23:33, 16 May 2026
Line 7:		Line 7:
	In my opinion, this later front end fits the "de-molded" 300ZX better than the original angular nose. Here’s what was required on my 300ZX (built June 1984) to install the later style nose. For example, see the pictures below: the '88 is on the right, the '84 is on the left.		In my opinion, this later front end fits the "de-molded" 300ZX better than the original angular nose. Here’s what was required on my 300ZX (built June 1984) to install the later style nose. For example, see the pictures below: the '88 is on the right, the '84 is on the left.

	![~~Nissan Egg](~~https://dev.z31library.com/xenonzcar_archive/z31/images/Colors ~~on a z~~/526 ~~NissanEgg~~.jpg)		![https://dev.z31library.com/xenonzcar_archive/z31/images/Colors%20on%20a%20z/526%20NissanEgg.jpg Nissan Egg]

	![~~Color 526](~~https://dev.z31library.com/xenonzcar_archive/z31/images/Colors ~~on a z~~/526.jpg)		![https://dev.z31library.com/xenonzcar_archive/z31/images/Colors%20on%20a%20z/526.jpg Color 526]

	=== Parts Needed ===		=== Parts Needed ===
Line 30:		Line 30:
	The '87 headlamp buckets use different mounting points than the '84. The approximate location of the different mounting points is shown in green below:		The '87 headlamp buckets use different mounting points than the '84. The approximate location of the different mounting points is shown in green below:

	![~~Headlamp Bucket Mounting Points](~~https://dev.z31library.com/xenonzcar_archive/z31/images/Front ~~swap 87 on 86~~/87frontconverttip2.png)		![https://dev.z31library.com/xenonzcar_archive/z31/images/Front%20swap%2087%20on%2086/87frontconverttip2.png Headlamp Bucket Mounting Points]

	2. Upper Bumper Mount Modification		2. Upper Bumper Mount Modification
Line 50:		Line 50:
	Here is what happens if you don’t trim the ends of the top mount and use the '84–'86 hood and headlights:		Here is what happens if you don’t trim the ends of the top mount and use the '84–'86 hood and headlights:

	![~~Incorrect Fitment Example](~~https://dev.z31library.com/xenonzcar_archive/z31/images/Front ~~swap 87 on 86~~/87on86full.png)		![https://dev.z31library.com/xenonzcar_archive/z31/images/Front%20swap%2087%20on%2086/87on86full.png Incorrect Fitment Example]

	=== Headlamp Fitment ===		=== Headlamp Fitment ===

XenonzcarImporter: Inline image refs: rewrite to local archive; clean empty image artifacts

2026-05-16T18:01:26Z

Inline image refs: rewrite to local archive; clean empty image artifacts

Show changes

XenonzcarImporter: XenonzcarImporter moved page Sites/Xenonzcar/z31/Frontendconversion php to Z31/Frontendconversion php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

2026-05-16T06:38:38Z

XenonzcarImporter moved page Sites/Xenonzcar/z31/Frontendconversion php to Z31/Frontendconversion php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

← Older revision		Revision as of 06:38, 16 May 2026
(No difference)

XenonzcarImporter: Site import

2026-05-16T06:27:03Z

Site import

New page

{{ImportedFrom|site=Xenonzcar|title=Z31 Zenki to Kouki 1984-1986 to 1987-1989 Front Body Conversion|url=http://www.xenonzcar.com/z31/Frontendconversion.php.html|archive=https://dev.z31library.com/xenonzcar_archive/z31/Frontendconversion.php.html|fetched=2026-05-15}}

== Z31 Zenki to Kouki 1984-1986 to 1987-1989 Front Body Conversion ==

The 300ZX was slightly redesigned for the 1987 model year to boost sales, as the original design "dated quickly." The update included a redesigned nose and hood, larger wheels, and a new tail design. The front became less angular, the bumper extended less under the car, the fog lamps were moved into the bumper, and a wider, replaceable bulb headlamp was used.

In my opinion, this later front end fits the "de-molded" 300ZX better than the original angular nose. Here’s what was required on my 300ZX (built June 1984) to install the later style nose. For example, see the pictures below: the '88 is on the right, the '84 is on the left.

![Nissan Egg](http://xenonzcar.com/z31/images/Colors on a z/526 NissanEgg.jpg)

![Color 526](http://xenonzcar.com/z31/images/Colors on a z/526.jpg)

=== Parts Needed ===

* Hood
* Bumper cover (the plastic skin)
* Bumper reinforcement (the actual metal bumper)
* Foglamps (if you can find them)
* Headlamp buckets (complete with headlamps, wiring, and covers)
* Hood safety Catch Support

=== Bumper and Hood Fitment ===

The hood should bolt on without any problems. I used the hinges from the '87 donor car and they bolted right up; if you're having issues, try those.

As for the bumper, there are two main hurdles that make this a non-bolt-on installation.

1. Headlamp Bucket Mounting Points

The '87 headlamp buckets use different mounting points than the '84. The approximate location of the different mounting points is shown in green below:

![Headlamp Bucket Mounting Points](http://www.xenonzcar.com/z31/images/Front swap 87 on 86/87frontconverttip2.png)

2. Upper Bumper Mount Modification

The '87 upper bumper mount isn't as long as the one on the '84. To allow the mount to bolt up properly, about 1/4" of material had to be cut from the ends as outlined in green. I used an angle grinder with a cutoff wheel—took about 10 seconds each side.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87frontconverttip6.jpg image: Bumper Mount Modification]

This is what was removed. The upper mount bolted right up with this material gone.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87frontconverttip5.jpg image: Material Removed from Upper Mount]

Aside from those points, all other mounting points appear to be in the appropriate spots:

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87frontconverttip1.jpg image: Mounting Points 1]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87frontconverttip3.jpg image: Mounting Points 2]

Here is what happens if you don’t trim the ends of the top mount and use the '84–'86 hood and headlights:

![Incorrect Fitment Example](http://www.xenonzcar.com/z31/images/Front swap 87 on 86/87on86full.png)

=== Headlamp Fitment ===

From what I've read, the headlamp buckets should simply require drilling a couple of new holes and bending the base of the bucket. For some (perhaps '86 model year), this is the case. Unfortunately, for me, it was substantially more involved—but the result looks factory.

Here is a side-by-side comparison of the '87 and '84 style headlamp buckets. They are laying headlamps down—the '87 is on the left. Notice the '87 bucket is substantially deeper than the '84.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp1.jpg image: '87 vs '84 Headlamp Buckets]

As you might guess, when the '87 headlamps are installed on the '84, they won't recess—the '84 bucket is not deep enough to accept the '87 assembly.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp2.jpg image: '87 Headlamp Not Recessed]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp3.jpg image: Another Angle - Not Recessed]

To fit the '87 headlamp, the front metal piece must be removed. Based on the height the headlamp stuck up above the hood, approximately 3" of material had to be cut out. I used a 4 1/2" angle grinder with a 36-grit cutoff wheel—disheartening, but necessary!

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp4marked.jpg image: Marked Area for Cutting]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp4.jpg image: Metal Piece Removed]

The '87 headlamp mounts to the car differently than the '84. There are two studs on the bottom of the headlamp that mount through the bottom of the bucket. These must be drilled out to fit the '87 headlamp. To do this, I painted the studs with fluorescent paint and installed them, then drilled holes where the paint marked.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp5.jpg image: Studs Marked for Drilling]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp6.jpg image: Drilled Mounting Holes]

I had to drill a couple of holes to get the left stud to line up. Additionally, I had to elongate the holes until everything adjusted correctly.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp12.jpg image: Elongated Mounting Holes]

The '84 headlamp bucket is too deep on the inner edge, causing the headlamp to tilt toward the radiator. To fix this, the bottom of the bucket must be bent upward by approximately 1–2". I used a body hammer with good results.

Once the holes were drilled and the bucket bent, I test fit the headlamp. The brackets that mount the bucket to the radiator support were too short—the bucket stood about 1/2" above the hood. To fix this, I cut off the brackets with the angle grinder and welded on replacements from 1/8" mild steel.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp7.jpg image: Short Mounting Bracket]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp8.jpg image: Replacement Bracket Welded]

With everything modified, I then spent about 2 hours bending, tweaking, and adjusting to get the headlamp to sit flush and properly angled with the hood. When everything finally lined up, I tack welded spacers to each mounting point so the headlamp would align again when removed.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp9.jpg image: Final Mounting Adjustments]

Once installed and aligned, I rebuilt the front metal piece using 22-gauge steel, moving it outward about 3/4" from the original. (The funky-looking black stuff is just a weird reflection.)

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp11.jpg image: Rebuilt Front Metal Piece]

When everything fits as desired, brush all welds and seams with 3M's brushable seam sealer. Re-undercoat the base of the bucket and repaint the radiator support panel, bucket sides, and new bucket frame to match the underhood black.

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/headbucketfin2.jpg image: Finished Bucket Area]

And the final results: This took me about 4 hours nonstop. Hopefully, the passenger side will go even faster with the experience gained!

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp10.jpg image: Final Installed Result 1]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/87headlamp13.jpg image: Final Installed Result 2]

=== Final Steps and Thoughts ===

To finish the installation, all welds will be coated with 3M's seam sealer and all surfaces painted black. The undercoating will be reapplied to both the inside and underside of the headlamp buckets. The headlamp buckets will be rebuilt to like-new condition, just as with the originals. Additionally, I plan to use aftermarket foglamps—these offer substantially higher quality for less than replacement units from the dealership.

Here are a few pictures taken just because... hopefully, they'll motivate you either for or against this conversion if you're considering it but not sure you want to take it on:

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/DSC03647.jpg image: Conversion Complete - Front Angle]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/DSC03648.jpg image: Conversion Complete - Side View]

[http://www.xenonzcar.com/z31/images/Raredare1/frontconversion/DSC03649.jpg image: Conversion Complete - Detail]

The grey strip along the bumper will be continued along the fender, using strips formed from fiberglass.

=== Sources Used ===

* Writen by: Radare

[[Category:Imported from Xenonzcar]]

Z31/Frontendconversion php - Revision history

XenonzcarImporter: Fix: convert markdown link syntax to wiki syntax; remove broken self-anchor links

XenonzcarImporter: Inline image refs: rewrite to local archive; clean empty image artifacts

XenonzcarImporter: XenonzcarImporter moved page Sites/Xenonzcar/z31/Frontendconversion php to Z31/Frontendconversion php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

XenonzcarImporter: Site import