S130/crxseats php - Revision history

XenonzcarImporter: Inline image refs: rewrite to local archive; clean empty image artifacts

2026-05-16T18:01:22Z

Inline image refs: rewrite to local archive; clean empty image artifacts

← Older revision		Revision as of 18:01, 16 May 2026
Line 1:		Line 1:
	{{ImportedFrom\|site=Xenonzcar\|title=CRX Seats in an S130\|url=~~http~~://~~www~~.~~xenonzcar~~.com/s130/crxseats.php.html\|archive=https://dev.z31library.com/xenonzcar_archive/s130/crxseats.php.html\|fetched=2026-05-15}}		{{ImportedFrom\|site=Xenonzcar\|title=CRX Seats in an S130\|url=https://dev.z31library.com/xenonzcar_archive/s130/crxseats.php.html\|archive=https://dev.z31library.com/xenonzcar_archive/s130/crxseats.php.html\|fetched=2026-05-15}}

	== CRX Seats in an S130 ==		== CRX Seats in an S130 ==
Line 21:		Line 21:
	Drill a new hole in the front (or rear) of the rail that has 12" centers.		Drill a new hole in the front (or rear) of the rail that has 12" centers.

	~~[http~~://~~www~~.~~xenonzcar~~.com/s130/images/seatrail.jpg ~~image: ZX seat rail modification]~~		https://dev.z31library.com/xenonzcar_archive/s130/images/seatrail.jpg

	'''Item 1:''' New hole drilled 12 inches from the rear mounting hole (Datsun spacing is 12.5 inches).		'''Item 1:''' New hole drilled 12 inches from the rear mounting hole (Datsun spacing is 12.5 inches).
Line 27:		Line 27:
	'''Item 2:''' Remove the wire that connects here and cut off the tab that sticks up, as it will cause clearance problems under the seat.		'''Item 2:''' Remove the wire that connects here and cut off the tab that sticks up, as it will cause clearance problems under the seat.

	~~[http~~://~~www~~.~~xenonzcar~~.com/s130/images/spacer.jpg ~~image: Copper spacer]~~		https://dev.z31library.com/xenonzcar_archive/s130/images/spacer.jpg

	1-inch copper spacer, cut in half. Install under the mounting bolt on the front of both seats.		1-inch copper spacer, cut in half. Install under the mounting bolt on the front of both seats.

	~~[http~~://~~www~~.~~xenonzcar~~.com/s130/images/spacerinstall.jpg ~~image: Spacer installed on seat rail]~~		https://dev.z31library.com/xenonzcar_archive/s130/images/spacerinstall.jpg

	1/2-inch spacer under front bolts, installed on both sides of the front rail. Two washers under the rear bolt on all rails (about 1/8-inch spacing).		1/2-inch spacer under front bolts, installed on both sides of the front rail. Two washers under the rear bolt on all rails (about 1/8-inch spacing).

	~~[http~~://~~www~~.~~xenonzcar~~.com/s130/images/hammerpoints.jpg ~~image: Hammered clearance points]~~		https://dev.z31library.com/xenonzcar_archive/s130/images/hammerpoints.jpg

	Arrows point to areas that needed a little hammer work for additional adjuster arm clearance.		Arrows point to areas that needed a little hammer work for additional adjuster arm clearance.

	~~[http~~://~~www~~.~~xenonzcar~~.com/s130/images/seatinstalled.jpg ~~image: CRX seats installed in 280ZX]~~		https://dev.z31library.com/xenonzcar_archive/s130/images/seatinstalled.jpg

	The final product: CRX seats installed in a 280ZX.		The final product: CRX seats installed in a 280ZX.

XenonzcarImporter: XenonzcarImporter moved page Sites/Xenonzcar/s130/crxseats php to S130/crxseats php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

2026-05-16T06:38:33Z

XenonzcarImporter moved page Sites/Xenonzcar/s130/crxseats php to S130/crxseats php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

← Older revision	Revision as of 06:38, 16 May 2026
(No difference)

XenonzcarImporter: Site import

2026-05-16T06:26:11Z

Site import

New page

{{ImportedFrom|site=Xenonzcar|title=CRX Seats in an S130|url=http://www.xenonzcar.com/s130/crxseats.php.html|archive=https://dev.z31library.com/xenonzcar_archive/s130/crxseats.php.html|fetched=2026-05-15}}

== CRX Seats in an S130 ==

Are your seats worn out, Torn, sagging? Here we replace the stock 280ZX seats with a set of seats from a second gen CRX.

=== Installation ===

The seats are from a 1991 Honda CRX Si.

The car is a 1982 280ZX 2+2.

The install will be the same on 2-seater Z's as on the 2+2.

I used the ZX seat rails, which hold the seat belt. This solves the problem of devising a custom mounting system had I chosen to use other seat rails.

Remove the seats (14mm bolts) and remove the rails from the bottom of the 280ZX seats. Remove and discard the wire going between the two locks on the sliders.

The outside rails that do not have the seatbelt or slider adjuster are the first to work on. Drill out the two rivets holding the “lock” plate down and discard the plate. This allows the outside rails to slide without locking. The inside rail lock will be sufficient and avoids clearance issues with both locks.

Drill a new hole in the front (or rear) of the rail that has 12" centers.

[http://www.xenonzcar.com/s130/images/seatrail.jpg image: ZX seat rail modification]

'''Item 1:''' New hole drilled 12 inches from the rear mounting hole (Datsun spacing is 12.5 inches).

'''Item 2:''' Remove the wire that connects here and cut off the tab that sticks up, as it will cause clearance problems under the seat.

[http://www.xenonzcar.com/s130/images/spacer.jpg image: Copper spacer]

1-inch copper spacer, cut in half. Install under the mounting bolt on the front of both seats.

[http://www.xenonzcar.com/s130/images/spacerinstall.jpg image: Spacer installed on seat rail]

1/2-inch spacer under front bolts, installed on both sides of the front rail. Two washers under the rear bolt on all rails (about 1/8-inch spacing).

[http://www.xenonzcar.com/s130/images/hammerpoints.jpg image: Hammered clearance points]

Arrows point to areas that needed a little hammer work for additional adjuster arm clearance.

[http://www.xenonzcar.com/s130/images/seatinstalled.jpg image: CRX seats installed in 280ZX]

The final product: CRX seats installed in a 280ZX.

=== Sources Used ===

* Write-up By Bleach of
[http://www.zdriver.com zdriver.com]

[[Category:Imported from Xenonzcar]]