Plugs - Revision history

XenonzcarImporter: Inline image refs: rewrite to local archive; clean empty image artifacts

2026-05-16T18:01:21Z

Inline image refs: rewrite to local archive; clean empty image artifacts

← Older revision		Revision as of 18:01, 16 May 2026
Line 1:		Line 1:
	{{ImportedFrom\|site=Xenonzcar\|title=Reading Your Spark Plugs\|url=~~http~~://~~www~~.~~xenonzcar~~.com/Plugs.html\|archive=https://dev.z31library.com/xenonzcar_archive/Plugs.html\|fetched=2026-05-15}}		{{ImportedFrom\|site=Xenonzcar\|title=Reading Your Spark Plugs\|url=https://dev.z31library.com/xenonzcar_archive/Plugs.html\|archive=https://dev.z31library.com/xenonzcar_archive/Plugs.html\|fetched=2026-05-15}}

	Engine problems can be difficult to diagnose. While this guide may not be the ultimate solution to your engine problems, being able to get some insight from the condition of your spark plugs will at least give you a starting point.		Engine problems can be difficult to diagnose. While this guide may not be the ultimate solution to your engine problems, being able to get some insight from the condition of your spark plugs will at least give you a starting point.
Line 5:		Line 5:
	\|		\|
	=== Possible Diagnosis \| ===		=== Possible Diagnosis \| ===
	~~![]() \|~~
	=== Normal ConditionAn engine's condition can be judged by the appearance of the spark plug's firing end. If the firing end of a spark plug is brown or light gray, the condition can be judged to be good and the spark plug is functioning optimally. \| ===		=== Normal ConditionAn engine's condition can be judged by the appearance of the spark plug's firing end. If the firing end of a spark plug is brown or light gray, the condition can be judged to be good and the spark plug is functioning optimally. \| ===
	~~![]() \|~~
	=== Dry or Wet FoulingAlthough there are many different cases, if the insulation resistance between the center electrode and the shell is over 10 ohms, the engine can be started normally. If the insulation resistance drops to 0 ohms, the firing end is fouled by either wet or dry carbon. \| ===		=== Dry or Wet FoulingAlthough there are many different cases, if the insulation resistance between the center electrode and the shell is over 10 ohms, the engine can be started normally. If the insulation resistance drops to 0 ohms, the firing end is fouled by either wet or dry carbon. \| ===
	~~![]() \|~~
	=== OverheatingWhen a spark plug overheats, deposits that have accumulated on the insulator tip melt and give the insulator tip a glazed or glossy appearance. \| ===		=== OverheatingWhen a spark plug overheats, deposits that have accumulated on the insulator tip melt and give the insulator tip a glazed or glossy appearance. \| ===
	~~![]() \|~~
	=== DepositsThe accumulation of deposits on the firing end is influenced by oil leakage, fuel quality and the engine's operating duration. \| ===		=== DepositsThe accumulation of deposits on the firing end is influenced by oil leakage, fuel quality and the engine's operating duration. \| ===
	~~![]() \|~~
	=== Lead FoulingLead fouling usually appears as yellowish brown deposits on the insulator nose. This can not be detected by a resistance tester at room temperature. Lead compounds combine at different temperatures. Those formed at 370-470°C (700-790°F) having the greatest influence on lead resistance. \| ===		=== Lead FoulingLead fouling usually appears as yellowish brown deposits on the insulator nose. This can not be detected by a resistance tester at room temperature. Lead compounds combine at different temperatures. Those formed at 370-470°C (700-790°F) having the greatest influence on lead resistance. \| ===
	~~![]() \|~~
	=== BreakageBreakage is usually caused by thermal expansion and thermal shock due to sudden heating or cooling. \| ===		=== BreakageBreakage is usually caused by thermal expansion and thermal shock due to sudden heating or cooling. \| ===
	~~![]() \|~~
	=== Normal LifeA worn spark plug not only wastes fuel but also strains the whole ignition system because the expanded gap (due to erosion) requires higher voltages. ===		=== Normal LifeA worn spark plug not only wastes fuel but also strains the whole ignition system because the expanded gap (due to erosion) requires higher voltages. ===
	\|		\|
	~~![]() \|~~
	=== Abnormal ErosionAbnormal electrode erosion is caused by the effects of corrosion, oxidation and reaction with lead - all resulting in abnormal gap growth. \| ===		=== Abnormal ErosionAbnormal electrode erosion is caused by the effects of corrosion, oxidation and reaction with lead - all resulting in abnormal gap growth. \| ===
	~~![]() \|~~
	=== MeltingMelting is caused by overheating. Mostly, the electrode surface is rather lustrous and uneven. The melting point of nickel alloy is 1,200~1,300°C (2,200~2,400°F). \| ===		=== MeltingMelting is caused by overheating. Mostly, the electrode surface is rather lustrous and uneven. The melting point of nickel alloy is 1,200~1,300°C (2,200~2,400°F). \| ===
	~~![]() \|~~
	=== Erosion, Corrosion and OxidationThe material of the electrodes has oxidized, and when the oxidation is heavy it will be green on the surface. The surface of the electrodes is also fretted and rough. \| ===		=== Erosion, Corrosion and OxidationThe material of the electrodes has oxidized, and when the oxidation is heavy it will be green on the surface. The surface of the electrodes is also fretted and rough. \| ===
	~~![]() \|~~
	=== Lead ErosionLead erosion is caused by lead compounds in the gasoline which react chemically with the material of the electrodes (nickel alloy) as high temperatures; crystal of nickel alloy fall off because of the lead compounds permeating and seperating the grain boundary of the nickel alloy. Typical lead erosion causes the surface of the ground electrode to become thinner, and the tip of the electrode looks as if it has been chipped. \| ===		=== Lead ErosionLead erosion is caused by lead compounds in the gasoline which react chemically with the material of the electrodes (nickel alloy) as high temperatures; crystal of nickel alloy fall off because of the lead compounds permeating and seperating the grain boundary of the nickel alloy. Typical lead erosion causes the surface of the ground electrode to become thinner, and the tip of the electrode looks as if it has been chipped. \| ===

	[[Category:Imported from Xenonzcar]]		[[Category:Imported from Xenonzcar]]

XenonzcarImporter: XenonzcarImporter moved page Sites/Xenonzcar/Plugs to Plugs without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

2026-05-16T06:38:32Z

XenonzcarImporter moved page Sites/Xenonzcar/Plugs to Plugs without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

← Older revision	Revision as of 06:38, 16 May 2026
(No difference)

XenonzcarImporter: Site import

2026-05-16T06:26:00Z

Site import

New page

{{ImportedFrom|site=Xenonzcar|title=Reading Your Spark Plugs|url=http://www.xenonzcar.com/Plugs.html|archive=https://dev.z31library.com/xenonzcar_archive/Plugs.html|fetched=2026-05-15}}

Engine problems can be difficult to diagnose. While this guide may not be the ultimate solution to your engine problems, being able to get some insight from the condition of your spark plugs will at least give you a starting point.

|
=== Possible Diagnosis | ===
![]() |
=== Normal ConditionAn engine's condition can be judged by the appearance of the spark plug's firing end. If the firing end of a spark plug is brown or light gray, the condition can be judged to be good and the spark plug is functioning optimally. | ===
![]() |
=== Dry or Wet FoulingAlthough there are many different cases, if the insulation resistance between the center electrode and the shell is over 10 ohms, the engine can be started normally. If the insulation resistance drops to 0 ohms, the firing end is fouled by either wet or dry carbon. | ===
![]() |
=== OverheatingWhen a spark plug overheats, deposits that have accumulated on the insulator tip melt and give the insulator tip a glazed or glossy appearance. | ===
![]() |
=== DepositsThe accumulation of deposits on the firing end is influenced by oil leakage, fuel quality and the engine's operating duration. | ===
![]() |
=== Lead FoulingLead fouling usually appears as yellowish brown deposits on the insulator nose. This can not be detected by a resistance tester at room temperature. Lead compounds combine at different temperatures. Those formed at 370-470°C (700-790°F) having the greatest influence on lead resistance. | ===
![]() |
=== BreakageBreakage is usually caused by thermal expansion and thermal shock due to sudden heating or cooling. | ===
![]() |
=== Normal LifeA worn spark plug not only wastes fuel but also strains the whole ignition system because the expanded gap (due to erosion) requires higher voltages. ===
|
![]() |
=== Abnormal ErosionAbnormal electrode erosion is caused by the effects of corrosion, oxidation and reaction with lead - all resulting in abnormal gap growth. | ===
![]() |
=== MeltingMelting is caused by overheating. Mostly, the electrode surface is rather lustrous and uneven. The melting point of nickel alloy is 1,200~1,300°C (2,200~2,400°F). | ===
![]() |
=== Erosion, Corrosion and OxidationThe material of the electrodes has oxidized, and when the oxidation is heavy it will be green on the surface. The surface of the electrodes is also fretted and rough. | ===
![]() |
=== Lead ErosionLead erosion is caused by lead compounds in the gasoline which react chemically with the material of the electrodes (nickel alloy) as high temperatures; crystal of nickel alloy fall off because of the lead compounds permeating and seperating the grain boundary of the nickel alloy. Typical lead erosion causes the surface of the ground electrode to become thinner, and the tip of the electrode looks as if it has been chipped. | ===

[[Category:Imported from Xenonzcar]]